How to Get a New Key for Subaru

If your subaru transponder key has keys, you can lock and unlock it at the push of the button. But, if your key fob gets dropped in the ocean or gets a bath in the washer and you are looking for a way to fix it.

Fortunately we at our Stocker subaru car keys replacement dealership has a few tips to help. You'll have to unzip the key fob case to locate the transmitter circuit.

How can I get a brand new key

It's easier than you think to purchase the new Subaru key. It's possible to obtain a new key at the dealer, an automotive locksmith or even online. The cost will vary based on the location where you purchase the key as well as if it is required to be programmed. It also depends on the type of key (transponder or smart fob? Push to start or regular non-transponder?)

If you're looking for a new key for your vehicle, it's best to call an auto locksmith who is experienced in Subaru cars. They'll know about the unique key fobs, as well as the key programming that is provided with them. If you're unsure which type of key you own, check the sticker on your windshield to figure it out.

Certain keys come with Remote Start features that allow you to start your car from the comforts of your home. You'll need to have the VIN number of the car key cutting service Near me that is located on the label inside the driver's door or in the owner's manual.

Subaru models that were manufactured after 2000 come with transponder keys that disable the engine computer. Keys cannot be duplicated using the same machines that cut keys made of metal. You will need to visit a dealership or locksmith for replacement keys. A new key can cost between $50 and $250, depending on the model.

How to get a replacement key

You can purchase a replacement Subaru key in several different ways, based on the type of vehicle you own (chip remote, intelligent or "push-to-start" remote or a standard metallic key). You can purchase a replacement key online or contact the dealership which you purchased the vehicle from or an auto locksmith that has the necessary equipment to make this type of key. If you purchase a new replacement key from the dealership it is guaranteed to work with your car and be covered by a warranty and will come with the correct program for your particular model.

If you want a chip-key it is necessary for the dealer to have the codes for your specific vehicle. This can only be done at the dealership from which you purchased the vehicle. This can be an inconvenience because you'll need to either bring your car to the dealer or let an automotive locksmith arrive and code the key on site.

A basic metal key is not required to be coded and can be duplicated by many locksmiths or hardware stores that have a wide range of keys that are blank. You'll need a steel key or flathead screwdriver to unlock the small tabs on the top of the key fob and let the battery go. Replace the battery with the CR 2032 coin cell, and put the encasement back in place.

How do I get a key fob

A key fob is a remote device that allows you to control the electrical systems. They can unlock and start your vehicle or lock it, set the alarm, and so on. It is possible to replace your Subaru key fob if it's not functioning correctly. However, you should make sure that you're getting the correct kind of fob for your vehicle. Consumer Reports says that off-brand fobs can cause problems with the immobilizer system in your vehicle.

If you own a newer Subaru, it's likely that it uses an intelligent key system. These require special programming to function with your vehicle. This should be handled by your dealer and the cost may be covered by your warranty or roadside assistance program.

Older Subaru models come with a standard metal lock that can be duplicated in an hardware store. You can also buy blank keys from online retailers that provide subaru key copy key chains with Subaru logos.

If your older Subaru is experiencing issues with its battery you can fix it yourself without visiting an expert mechanic or paying for a key duplicate service. Find a small crevice in the seam that divides the front and back of the fob. Make use of a flathead screwdriver to split the two halves. You'll find a flat-type battery in the inside. Replace the battery with a 2025-type one, making sure the correct side is facing up. Put the key of metal into the slot, and snap it together.

How do I replace a key fob

In the past it was typical for people to buy a cheap key fob from a hardware store online and take it to a locksmith or dealer to have it cut and programmed. While this is still an option, it's a better idea to contact the dealer to avoid the danger of having the key copied and to ensure that your new key fob has been properly programmed for your vehicle. This is crucial for vehicles with newer model that requires specialized programming, like ones with features like automatic parking and window rolling.

These fobs are convenient to use when driving your Subaru in Gilroy but can be an issue when their buttons stop working. You can replace the key fob's battery yourself, in case you're familiar with the process.

Start by finding the small space between the front and back of your key fob. Use the tips of a key made of metal or a flathead screwdriver to pop open the fob, and then look for the flat, round battery inside. Remove the old battery and then place a brand new 2032 battery into its place, ensuring it's facing the same direction as the original. Reassemble your device.

In the near future you may be able to get your car keys replaced with "smart" keys that offer additional functions. However, until then, you can enjoy all of the benefits of your Subaru's key fob. It includes its ability to automatically reduce your windows while keeping your engine running.