Reasons Your fiat car key 500 Key Fob Won't Work

A key fob for the fiat ducato key programming 500 is a convenient way to open the doors and start the car. There are many reasons why the fob may stop working. This could be due to a dead coin-battery and water damage, as well as issues with the receiver module, and interference.

This listing is for an NEW replacement fiat panda key Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths in the automotive industry). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason why your fiat 500 new key cost uk key fob won't function is a dead battery. Modern key fobs operate with a limited operating range, and must be within a few feet of the vehicle in order to function. If you are not within your vehicle and you push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) with a new one from a trusted brand such as Panasonic, Duracell, or Energizer. They are usually available at your local hardware store or on the internet.

You can test the battery of your coin-cell by pressing the buttons while standing near your fiat 500 replacement key cost 500. The car will blink its parking lights and the key fob should work the lock and unlock switches.

If your key fob isn't working even after replacing the battery, there might be water damage that prevents it from communicating with the module in your vehicle. Water damage can happen locked keys in car boot fiat punto many ways, including a simple splash or submerging your key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture out. If that doesn't work your fob may require reprogramming by a professional locksmith or dealer.

Water Damage

While the fob comes with rubber seals to keep water out of the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to become shorted and eventually cease to function. Getting the fob wet is not an option however, if you drop it into an empty cup of water, or don't remember to take it out of your pants pocket before running the washing machine do not give up hope.

Take the battery off first. Before replacing the battery clean the electronic chip with isopropyl, or a similar product. Then try the fob and verify if it is working. If the fob doesn't function, it may need to be reset. This is usually done by an auto locksmith or dealer.

If the key you have is older and is not programmed for your vehicle it is necessary to replace it completely. This is a straightforward process that can be carried out by a professional locksmith for automotive use. The locksmith will have to cut the key to match the ignition in your vehicle. They will also need to program the fob into the system of your car. This is a low-cost and quick procedure that can be completed on the same day.

Receiver Module Issues

Your 500 key fob may not work because it's out of range. The remote has a range of 30 feet, which means should you be too far from your car, it won't respond to your commands. It's easy to remedy this by moving your remote closer to your car until it responds.

If your fob isn't working after you replace the battery in the coin, also known as a "button", "watch" or "button", it could be due to a problem with the circuit board inside. In the majority of cases, reprogramming your fob can resolve the issue. You can find instructions on how to do this for all automobiles by searching YouTube or consulting the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they lose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances, the fob may become desync'd with your vehicle because of software or hardware issues. This can be a major headache, but you can often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob. In certain instances the software might require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit a signal. This may happen if the keyfob is in close proximity to a radio transmitter like a cellphone or radar detector. Other reasons the key fob could not function include a weak connection to the buttons, damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy way to reset all on-board systems in your 500 device, including the key fob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will clear any residual electrical charge, and then restart the car's computer. This will help you get your key fob to function again. If the problem persists, you should consult an experienced technician. They will be able diagnose the exact cause of any problems.