How to Repair Bifold Door Top Roller Guide

If your bifold door is sticking then it's likely that they need some attention. You may have to clean or lubricate them, or even adjust them. The issue could be caused by an unfastened bolt at the top pivot or by the top guide roller.

This kit includes all the hardware required to restore your bi fold door repairs-fold closet door system to its optimal performance.

Remove the Door

Installing an internal set of bifold doors could seem like a complex and difficult task however, it's actually easy for DIYers with a bit of experience. The frame isn't the problem, but getting the doors to fold and close smoothly is. Bifold doors are intricate pieces of machinery, and as such they could require some tuning up to ensure that they function properly. It could be as easy as tightening a screw, or as intricate as removing and replacing the door's pivot pin or roller.

The majority times, you can solve these issues by making a few simple adjustments, without having to remove the doors. You may notice that your doors are sagging, scratching the floor, or they are bouncing off of their tracks. The solution to these issues isn't difficult, and with three simple steps the bifold doors will be back on track in no time.

One of the most frequent issues that internal bifold doors encounter is sliding out of alignment. This can be due to loose screws, holes on the anchor/pivots, or a misaligned bifold door. In the majority of instances, you can fix this with a few easy adjustments, but if your door isn't moving at all it could be necessary to have it removed and replaced.

You'll need to remove the door using the help of a screwdriver and possibly a pair pliers to loosen any pivot pins that are tight. The screwdriver is used to disengage the locking levers located on the bottom bracket for pivots. The pliers are used to take off the pin.

Once the top roller has been removed Once the top roller is removed, you can raise the door, then swivel it downwards and remove it from its pivot brackets and track. This is usually quite straightforward, but be careful not to let the door hit against the frame of the door. You should then be able to cut off the edge of the door which is scratching the floor, and sand it down until it's smooth. Then paint or refinish the door if needed.

Remove the Roller Guide

This spring-loaded roller guide mounts on the top of bifold doors to aid in smooth operation. It is specifically designed to work with Kenna frames and will fit door panels that range from 1 inch to 1-3/8 inches thick. It is made from steel, nylon and plastic components and will replace a worn or damaged guide.

Remove any screws holding the guide to the roller using a screwdriver. Use your hands to slowly pull it from the frame. It might require some effort to take off the door, so you may need a friend to help you.

After the guide has been removed, carefully cut through the remaining finish around the foot of the new guide with a sharp blade to cut it off from the rod blank. This will make it easier to remove and ensure that there is no damage to the new guide foot. Be careful when doing this, as the guide foot is extremely sharp and could cause injury to your fingers or cut them.

You may have to use some force to remove the guide, but be careful not to chip or break the foot. After you've separated the old guide from the rod blank, be sure to take out all of the threads and epoxy remaining in the area the guide was attached. This will prevent future problems with the guide.

After you have removed the guide, you can test your new guide by putting it in its new location and applying a few rotations of masking tape or some type of guide tubing to secure it in place. This will let you double examine the guide's spacing and alignment to make sure everything is set up properly. It doesn't matter if you're looking at it from a distance or using the always accurate CRB Spine Finder and Deflection System This step is crucial to prevent any issues in the future.

If the guide is set properly and functions according to its intended function then the final step is to put the door back in its place. Remember to replace and tighten any screws or pins that you removed or loosen.

Take the Bottom Pivot off.

Bifold doors can be a beautiful feature for a home, but they often require to be tweaked or adjusted to ensure they are in good condition. While some of the less critical issues can be fixed with the doors still in place, others will require them to be removed. This guide will demonstrate how to remove the bifold internal bi-fold door repairs near me pins, rollers and pivots.

Gathering your tools is the first step. Making sure you have everything in place prior to time will make it easier later during the construction. You'll also require an plier and a screwdriver. You can purchase a basic set of tools at your local hardware store at a reasonable price. It's important to have some wood glue handy. This can be very useful when you need to fix any rollers back into their original position.

After gathering your tools then open the bifold doors and loosen the top track bracket with your screwdriver. Once the bracket is in place, you should be able to slide the door off the top track. It might take a bit of jiggling but it should come right off the track.

The pivot at the bottom of the frame will have to be removed. Close all doors in the interior prior to starting. This will make it easier to do instead of working from the inside. If the bottom track still appears to be in good condition, you can simply lift the door and remove the track.

If the track is damaged, then you'll need to replace it. Hardware stores sell replacement tracks for bifold doors as well as swinging closet doors. If the track is badly damaged, you may have to replace it completely.

Now that your track is repaired or replaced it is time to test the doors to ensure proper operation. Make sure that they are able to move smoothly between positions. You'll want to ensure that the edges of your door are in line to the frame when it is closed. If they're not, you'll have to adjust the top pivot bracket by tightening or loosening the bottom setscrew.

Replace the Roller

Bifold doors neatly enclose closets, laundry nooks and pantries, but only when they function properly. The bifold doors consist of two panels that are hinged and slide along a track at the top of the frame. Over time, the roller guides can wear out and cause the doors to slide. Replacing the guide roller takes only a few minutes, and basic tools.

The first step is removing the guide for your roller from the door panel. The bottom pivot bolt must be removed and the screw holding the guide to the top of the door panel should be loosened. Once the guide is removed and the door panel is lifted up and away from its track. Then using a wrench remove the top pivot bolt from the hole in the frame's header by loosening the nut.

Stanley, Cox and Acme offer a replacement top nylon roller with a 7/8-inch wheel that rests on a steel base. It mounts at the top of bifold doors that range from 1 inch to 1-3/8 inch thick. It is spring-loaded and adjusts automatically in the upper track to ensure smooth sliding.

bifold doors repair doors can also scratch the floor as it closes and opens. This can occur after installing carpet or other flooring materials that require the doors to be slightly raised to allow for clearance. Removal of the bottom pivot adjustment screw and loosening the top track's mounting screws and moving the anchor/pivot pin is usually enough to clear this issue.

A new set of roller guides can be an inexpensive solution to your bifold doors being difficult to operate. They're usually available at the hardware store near you in the door section, however, they are also available on the internet from a variety of sellers. In addition to a new top guide for rollers, you'll need a small container of Elmer's wood glue that is sold in large box stores as well as a squeeze clamp. The clamp is used to keep the repair area tightly closed after glue is inserted, and allowed to dry.